T-Shirt Monstar Pot Holders

Materials Needed:
• old t-shirts or scrap material
• quilt batting
• sewing machine & thread
• needle & thread
• scissors




*close up


*close up

To make these fun little pot holders I grabbed some of my scrap t-shirt material and picked the one I wanted for the background and cut out a "square" (no exact measurements again). I used that first one I cut out as a template to cut out another of the same fabric and 2 of a different fabric for the back. Next, using my template, I cut out some quilt batting the same size (you will need at least 2, I used 4 because I wanted mine to be well insulated). I machine sewed the bating to the fabric, right side of fabric out. I did this for the other 3 sides as well. Then I took my 2 front pieces and cut out shapes from my other scrap t-shirt material and made my monstar on top. When I got it the way I wanted it I hand stitched the monstar onto the top fabric and top batting. When I was finished I put the monstar facing down on top of the back piece facing up (right sides together) and stitched with my machine all the way around leaving a large gap to flip it inside out. The first time I didn't leave enough space to flip it forgetting how bulky it would be with the 2 layers of batting so I had to seam rip it and re-sew. Then once it was flipped inside out I hand sewed it shut.

Picture Frame

Materials Needed:
• picture frame
• scrap pieces of paper
• Mod Podge
• vinyl contact paper
• etching cream
• silk flowers
• rhinestones
• craft knife
• 2 photos
• cardboard
• hot glue & hot glue gun



This is a frame I made for my little sis who is going to camp for 3 weeks. I wanted it to be fun and funky and several layers. I bought a frame that was simple but had a 3-dimensional quality since I had planned to make it with layers. Then I grabbed my scrap pieces of paper and Mod Podge and decoupaged the frame (I took out the glass and mat board and back piece off). On the back area where the back piece would fit in I tried to keep any paper and Mod Podge off of it (it didn't work out to well but I will get to that).

While I waited for the sides to dry I got the glass and cleaned it thoroughly and then placed the vinyl contact paper on top of the glass where I wanted to etch the glass (it's a bit hard to see all the etching in the photo above but it adds a nice frosted layer to the frame). When they vinyl contact paper was in place and the bubbles smoothed out I drew a leaf vine type design on 2 of the corners and then got my craft knife and cut out the design. Next I got the etching cream and brushed it on according to the instructions and waited the directed amount of time. Then I rinsed it off thoroughly in warm water and took the stencil off then cleaned the glass again.

When the frame was dried I placed the etched glass into the frame. Then I printed out the photos I wanted to use. One for the foreground cut out collage style and black and white and the other to be the main picture. Then I figured out where I wanted the front picture to be placed and hot glued cardboard behind it to make it more 3-dimensional.

Once the pictures were in place I put the back of the frame on, which as you know I had some issues with- I guess some Mod Podge or paper got into the spot or something. So I grabbed my craft knife and trimmed the back board to fit into the frame snugly.

Once that was all done I hot glued little purple bows and some of those silk flowers I have lying around and rhinestones on top. Now she will have a nice handmade picture frame to bring with her to camp.

Recycled Jar Lid Collage

Materials needed:
• jar lid (mine had about a 3 in. diameter)
• Mod Podge
• paint brush
• scrap paper
• scrap ribbon
• scrap felt
• photo (I printed mine out after resizing it to fit into the 3 in. jar lid)
• cardboard scraps
• glue on jewels
• hot glue




This idea sort of came to me after finding this lids that I had saved to one day do a craft project with (that was like 3 years ago) and so I decided it was time to use them. At first I just Mod Podged the pictures in and painted the Mod Podge on top and added some of the jewels. It looked alright but I wanted to add an element of fun to it, so I went back to the drawing board and came up with the idea of a 3-D collage lid.

First, I got a picture of my husband and I at our wedding and printed it out (sized to fit my 3 in. diameter). Then I traced the lid onto a sheet of scrap paper and cut a circle out (cutting inside the edge a bit so that it would fit). I did this to the polka dot paper and the pink tree paper-both being cut into circles. Then I put the polka dot one for the background in the lid and used Mod Podge all over. Then I took my pink paper and drew a tree shape on the back side and cut it out. Then I used the Mod Podge and placed the tree inside the lid.

Next I took the photo and cut out the background and cut the bottom into a circular shape to fit the lid. I glued the photo to a scrap piece of cardboard and then hot glued it into the lid. Then I cut out a heart out of some orange scrap paper and painted some glitter on it then glued some thinner cardboard to it and glued it behind out heads. Then I got some glue on jewels and made little blossoms for the tree.

Then I got some scrap ribbons and took a white one with wire and scrunched it around the back hot gluing as I went. Next I took a thin ribbon and glues it on the edges of the lid. To finish the back I cut out a felt circle and hot glued it to the back of the lid.

I am not sure yet what this will be but it can be a magnet by gluing a magnet on or I may hang a piece of ribbon from it and make it a hanging picture or an ornament for our tree this year. Not sure yet but there are a few possibilities for sure.

Decoupage Box

Materials needed:
• box
• scrap paper
• Mod Podge
• paint brush/sponge brush



This project came about yesterday morning when I picked up a box of my stamps and it fell apart. I decided to decoupage it using some old scraps of paper left over from a scrap book I made my little sis and news paper.

First, I cut the box top off (I used a shoe box that had a flip top-some have a removable top and then of course you don't have to cut it off) and then I proceeded to paint the Mod Podge on a small area and then placed scraps of paper down and brushed the Mod Podge on top. (I really love Mod Podge- it's a glue and a sealant!) I continued doing this until the whole bottom and top of the box were covered (I included a piece with stamps stamped out on it to let me know what was in the box). When it was all dry I took some book binding tape (I had some but if you don't you can use duct tape) and taped the top back on. I did it this way because when I try to leave the top on it inevitably seems to get so thick on the hinge I can't shut it. Then it was finished and I could place my stamps inside their new sturdy box. What is great about this box is that if I decided to change the contents I can just make a new piece with the content title and use my Mod Podge on it and voila- a new box.

Recycled Scrap T-Shirt Monstars

Materials needed:
• scrap material
• snap on eyes (available at craft stores)
• sewing machine (optional- can be hand sewn) & thread
• felt (optional for details- you could also use fabric paint or embroider details)
• yarn (optional for hair or other details)
• ribbon (optional for details)






Another super simple and fun project to do with some scrap pieces of fabric!

I made the top one out of scraps from my little sister's t-shirt purse I made her (the t-shirts were one's that she no longer fit in). The bottom one was just some scrap material I had lying around.

The idea is simple. I quickly drew a random shape and cut out 2 from either the same fabric (like in my second one) or different fabrics (like in the first one) and sewed all around the edges leaving a small space to flip it inside out. Once it was sewed clip around the curves (I normally clip the edges a lot when working with t-shirt material because it won't unravel). Then I flipped it inside out.

Next I added face details. With these 2 monstars I made felt mouths (including teeth on the bottom monstar) and then I got these plastic snap on eyes that you can get then at fabric and craft stores (what I love about these is they are super simple but instantly give it some personality). To attach the eyes you simply cut a small slice where you want them to go and then place the top of the eye through the hole and then using your opening on the bottom put your bottom eye attachment on to snap tight and keep the eye in place. You can also use buttons or felt or whatever you have lying around that would work for your monstar (that is one thing I love about making monstars is that no one knows what they are supposed to look like so you can make them look like whatever!)

After the face is done you can add little details like a belly, hair (on my bottom monstar), bow (on my top monstar) or whatever (again open to your interpretation). To make the hair I used some scrap yarn I had and cut it into longish stripes then sewed it down, when that was done I gave him a hair cut and styled it short and punky! For the belly I just sewed on a felt oval shape, The bow was a scrap piece of ribbon that I tied and then hand stitched on.

Once all the details are done I stuffed it using fiber fill (you can also use scrap material or whatever is soft and fluffy and you have lying around. Fill your monstar up and then sew it shut using a slip stitch. Now you can cuddle with your cute little homemade monstar!