Duct Tape Rings

Materials Needed:
• Duct Tape
• scissors
• goo gone & rag (to clean your scissors)


*all three rings


*detail


*detail

This idea came to me last night while I was watching tv. I found a piece of Duct Tape I had placed on the coffee table (that is sometimes where the scrap Duct Tape ends up when I am working on my crafts) and I started folding it and thought it kind of looked like a ring since it was so small so then of course I had to make it into a ring (which ended up being a few rings). I used the same method as my Duct Tape headbands but smaller of course. The bow one is my favorite. It reminds me of that tying a string on your finger so that you don't forget something.

So to do this I grabbed the Duct Tape and measured it around my finger (another percise measurement). Then I cut it half lenthwise and placed one half on my coffee table and the other half I held it lengthwise and folded the bottom part up to the center and then folded the top down covering all the exposed sticky sides then I wrapped it around my finger and cut a tiny piece from my coffee table left overs and wrapped it around the open parts of the bent ring giving me a closed up ring.

Then I added the details. For the stripes I just cut tiny strips and placed them around the ring. When I did the bow I used the same method as making the ring but folded it into a bow and placed yellow tape around the center tightly to secure it to the ring as well as give it the center part of the bow. For the flower started off the same way as making the ring but instead of folding both the upper and lower sides down I just did the upper side and then while crunching it up together and wrapping it around itself (using the exposed sticky part to "glue" it together) I made a rose. Then to attach it I used tiny strips of Duct Tape (from my coffee table again) and wrapped it around in different directions until I felt it was secure.

Duct Tape Monstar Bookmark

Materials Needed:
• Duct Tape
• craft knife
• self healing cutting board
• paper & pencil


* front & back

This project is similar to the Duct Tape Monstar Coaster project I did earlier, only this time I made a cut out book mark that I so often find myself needing.

Once again I recommend the self healing cutting board this way you can stick the duct tape down and cut the shape you need with your craft knife.

To start I sketched out the design keeping it more vertical than horizontal. Then I used that to make some templates out of paper. Then I grabbed the color of Duct Tape I wanted to be my background and taped down a few strips overlapping about the width and height of how I wanted the book mark to be then I flipped it over and taped the other side so that I was left with the colored Duct Tape showing on both sides. Then I took the colors I wanted the body of my monstar to be and placed it down on the self healing cutting board and placed my template on top and cut out the monstars body. Then I peeled it up and placed it on the background piece. I continued this method until I had the entire front of the monstar done. Then I cut out around the entire monstar.

Once he was cut out I then turned it around and prepared to do the back side of my monstar. I started the same why by putting the Duct Tape down on the self healing cutting board but when I got to the template part I flipped it over to the wrong side facing up. Then I cut out my shapes and placed them on the back side of the background. Now my monstar is ready to snuggle up with a nice good book.

Duct Tape Monstar Coasters

Materials Needed:
• duct tape
• craft knife
• scissors
• self-healing cutting board



Duct tape is always a fun medium. For this project I highly recommend working on a self healing cutting board because you can stick the duct tape down on it to cut it and peel it off easily.

To start I got my self healing cutting board and taped strips of one color of the duct tape to make the background once I had one side down I flipped it over and placed strips of the same color down but in the opposite direction (ie. if you laid your first ones down horizontally the other side was laid down vertically giving it a more secured base). When I had a big enough area covered in duct tape front and back I cut out a square (this would be the size of the final coaster). Once that was done I created my monstars using by laying down a few strips of color for the monstar base and then I cut it out to the shape I wanted. Then I placed it on top of the square and trimmed off any that wasn't on the square. Then I added a duct tape boarder in a different color. To do this I just laid out a piece of duct tape and cut it in half length wise, then taped it on the sides and folded it over to the back. Then I would tape down a piece of the desired color and cut out little details that I wanted to add.

What is nice about working with duct tape- if you place something and want to change it you can easily pick it up and move it.

Duct Tape Headands

Materials needed:
• duct tape (any color or colors of your choice)
• headband
• craft knife
• scissors
• goo-gone (optional but I recommend this to keep your scissors and craft knife from getting gooped up)

Duct tape is always fun to work with. I have made wallets and purses but one day I decided to make a head band. I got an old one and ripped off the ribbon and covered it with duct tape. It was bright green with white roses. I gave it to my little niece and when she wore it to school all of her teachers wanted to know where she got it. So I was inspired to make more.

To do this project I ordered blank headbands online but you can also use old ones or buy a cheap one and revamp it.

I got multiple colors of duct tape (black, white, silver of course, pink, teal, green, orange, purple- I have seen other cool ones as well but I went with the solid colors that I could find).

To start this project I just jumped in and learned along the way the best way to go about it. I will try to share some of my tricks here and hopefully you will understand.

First I pulled a long piece of duct tape off the roll and stuck it to the headband underneath area. Then I snipped the corners off and placed little slits all around on the tape that overlapped the headband so I could lay it flat onto the headband. Then I taped those little overlapped parts down on the top. Next I got another big piece I placed on the top and did the same overlapping it to the bottom part. Then I added details such as stripes (which I did by ripping the duct tape into thin strips and positioning them on), bows (I find the best way is to fold down a little more than 1/3 and then fold in the other side so that no sticky side is showing, then I would take a small skinny piece of duct tape and tape it over for the middle part or I would just tie it into a bow), or flowers (again fold down 1/3 towards the sticky side and then I round off the corner I am starting with and then start twisting it up "fluffing" the sides as I go), and leaves (here I just place 2 pieces of duct tape on top of each other sticky sides together and cut out a leaf shape) then use duct tape to tape it together and then you have a stylish fun headband! (Props to my little sis for being my beautiful model).